|
回流焊参数
|
|
|
型号 MODEL
|
VS-1000II / NS-1000II
|
|
机体参数 GENERAL
|
|
|
外型尺寸(L*W*H) Outside Dimension(L*W*H)
|
6100x1353x1490mm
|
|
颜色 Standard Color
|
计算机灰 Computer Grey
|
|
重量 Weight
|
Approx.2450KG
|
|
加热区数量 Number Of Heating Zones
|
上Up10/下Bottom10
|
|
加热区长度 Length Of Heating Zones
|
3891mm
|
|
冷却区数量 Number Of Cooling Zones
|
2(内置)
|
|
排风量要求 Exhaust Volume
|
10 M3/ min x 2 (通道) Exhausts
|
|
控制部分参数 Standard Feature Of Control System
|
|
|
电气要求 Electric Supply Required
|
3 phase,380V 50/60Hz(optional: 3 phase,220V 50/60Hz 选配)
|
|
电源功率要求 Electric Power Required
|
80KW
|
|
启动功率 Power For Warm Up
|
36KW
|
|
正常功率消耗 Power Consumption
|
13KW
|
|
升温时间 Warming Time
|
约 Approx.25 minute
|
|
温度控制范围 Temp. Setting Range
|
室温 Room Temp. --- 300℃
|
|
温度控制方式 Temperature Control Method
|
PID闭环控制 + SSR驱动 / PID Close Loop Control + SSR Driving
|
|
温度控制精度 Temperature Control Precision
|
± 1.0℃
|
|
PCB板温分布偏差 Temperature Deviation on PCB
|
± 1.5℃ (by JT Board Test Standard)
|
|
加热器 Heating Element
|
Especial Heating elements For Long Life ;特制的特长寿命加热器
|
|
Commutated Element 整流板结构
|
Aluminium Alloy Plate铝板
|
Max. Temp. Gap Between Preheat & Reflow Setting
预热区和焊接区之间的{zd0}温度设定差值
|
80℃
|
Max. Temp. Gap Between Preheat Zones Setting
预热区之间的{zd0}温度设定差值
|
40℃
|
Max. Temp. Gap Between Reflow Zones Setting
焊接区之间的{zd0}温度设定差值
|
50℃
|
|
参数存储 Data Storage
|
可存多种生产设置参数与状况 Process Data and Status Storage (80GB)
|
|
异常报警 Abnormal Alarm
|
温度异常（恒温后超高温或超低温）Abnormal Temperature (Extra-high / Extra-low Temp.)
|
|
掉板报警 Board Dropped Alarm
|
三色信号灯: 黄-升温；绿-恒温；红-异常 Tower Light: Yellow–Warming; Green-Normal; Red-Abnormal
|
|
运输参数 Standard Features Of Conveyor System
|
|
|
导轨数量
|
1 Lane
|
|
Rail Structure 导轨结构
|
Subsection Integrated Type整体分段式Subsection Separate Control分段独立控制(Option选配)
|
|
PCB{zd0}宽度 Max.Width Of PCB
|
400mm (Option:610mm 选项)
|
|
导轨调宽范围/调宽形式
|
50--400mm(Option:50--610mm 选项)/电动 Motorized
|
|
Range Of Rail Width/Adjustment
|
|
|
部品高度 Components Clearance
|
PCB板上/下各25mm , Top/ Bottom Clearance of PCB is 25mm
|
|
运输方向 Converyor Direction
|
左向右(选配: 右向左) L→R (Option: R→L)
|
|
运输导轨固定方式 Fixed Rail Side
|
前端固定(选配:后端固定)Front Rail Fixed(Option:Rear Rail Fixed)
|
|
PCB运输方式 PCB Transmission Agent
|
空气炉 Air-Reflow = 链条+网带 Chain + Mesh ,氮气炉 N2-Reflow空气炉 Air-Reflow = 链条+网带 Chain + Mesh , 氮气炉 N2-Reflow = 链条 Chain (可选配网带 Mesh is option)
|
|
中央支撑 Center Support (选配 Option)
|
防止PCB板因过宽及元器件过重而弯曲变形 Preventing PCB warp such too wide and heavy component load
|
|
运输带高度 Converyor Height
|
900±20mm
|
|
运输速度 Converyor Speed Range
|
300～2000mm/min
|